Page 2 of 2
Re: Test
Posted: September 1st, 2016, 2:40 pm
by testitemqlstudop
Code: Select all
x = 23, y = 31, rule = B3/S23
7b9o$2b2o6bobo6b2o$5b2o2bobobo2b2o$2bo8bo8bo$3b2o2b2obobob2o2b2o
$4b4o7b4o$6b2ob2ob2ob2o$6bo4bo4bo$2bobo13bobo$3bo15bo$3b2o4b2ob2o
4b2o$4bo5bobo5bo$4b2ob4ob4ob2o$4b2ob2o2bo2b2ob2o$7bo7bo$6bo9bo$4b
o3bo5bo3bo$bo3bo2bo5bo2bo3bo$o21bo$b2ob2ob2o5b2ob2ob2o$7b3o3b3o$
bo3bob2obobob2obo3bo$2b2obo4bobo4bob2o$3bobobo2bobo2bobobo$4b2ob
ob2ob2obob2o$5bobo7bobo$8bo5bo$6bo9bo$6bo3bobo3bo$7bo2bobo2bo$8b
3ob3o!
Re: Test
Posted: September 1st, 2016, 2:41 pm
by testitemqlstudop
sheesh! gfind is such an ogre
Code: Select all
x = 4, y = 3, rule = B3/S23
ob2o$o2bo$3o!
Re: Test
Posted: September 1st, 2016, 2:41 pm
by testitemqlstudop
and gfind told me that was an puffer.
Re: Test
Posted: September 1st, 2016, 3:06 pm
by drc
Please use the edit button.
Re: Test
Posted: September 1st, 2016, 10:04 pm
by wildmyron
testitemqlstudop wrote:and gfind told me that was an puffer.
The puffer detection in gfind is very trigger happy. It will report all patterns that successfully manage to reproduce the candidate pattern after one period (or something like that - I'm a bit hazy on the details). It does that so that it is able to report any pattern which is potentially a puffer engine. Most of these candidate patterns subsequently fall apart when the smoke at the back interferes with the engine itself. I believe this preliminary puffer detection code was implemented like this because it is simple, and allows puffers with much higher period to be found without having to run gfind at that much higher period. This is essentially required to allow gfind to run in some reasonable time, especially for slower engines which can only support puffers of much larger period than gfind is able to handle.
To get any useful output from the puffer detection, run gfind with hashing disabled, i.e. use '/h0' (so that incorrectly detected candidates won't be discarded from the search) and tell it to output a large number of results, e.g. '/f1000'. Redirect the output to a file and you will then need to post-process the results to find out if any of those candidate patterns stabilise into an actual puffer. I've not used this option successfully, but I can say that you should expect the success rate to be very low.
Re: Test
Posted: September 3rd, 2016, 12:50 pm
by testitemqlstudop
this has unusually large stabilization time and make quite a big explosion.
Code: Select all
#CXRLE Pos=-9,-6 Gen=28
x = 14, y = 13, rule = B3/S23
7bo$6bobo$6bobo$7bo2$2b2o7b2o$2o2bo5bo2bo$2b2o7b2o2$7bo$6bobo$6bobo$7b
o!
Re: Test
Posted: September 3rd, 2016, 2:04 pm
by Rhombic
Very interesting pattern that could hint at an oblique spaceship!!! Obviously, probably not in life, but some related rule. Just look at the evolution in normal CGoL:
Code: Select all
x = 10, y = 7, rule = B3/S23
2o$bo2bo$o2b2ob2o$2bo5bo$b2o5bo$2b2o3bo$6bo!